A Barksdale Inc. Company
Instruments & Controls for Rotating Equipment in Demanding Applications
 

美国德纳科Dynalco公司及产品简介

   
 
 
  监视器和扫描仪
 
 
 
 
 
 
 
 
 
 
 

Since 2007

 

   


Dynalco Magnetic Pickups and Speed Sensors
传感器

 

Standard Magnetic Pickups
标准磁性传感器

标准磁性传感器用于大多数应用。这些传感器有两个插脚,可接受标准MS样式的连接器。它们有短、中、长和超长螺纹长度。灵敏度可以是标准的、高的或超高的。有时需要具有更高灵敏度的拾波器以在低速下产生更高的输出。Standard magnetic pickups are used for most applications. These pickups have 2 pins that will accept a standard MS style connector. They are available in short, medium, long and extra-long thread lengths. The sensitivity is available as either standard, high or ultra-high. A pickup with higher sensitivity is sometimes required to produce higher output at low speed.


Intrinsically-safe Magnetic Pickups
本安型磁性传感器

本安全型磁性传感器的输出电流有限,用于可能存在爆炸性气体的危险场所。这些皮卡将由CSA、UL或ATEX批准,阅读适用证书非常重要,证书中应说明批准地点、批准的产品以及安装说明。与标准拾音器类似,这些拾音器有两个插脚,可接受标准MS样式的连接器,并提供短和长螺纹长度。灵敏度可以是标准的,也可以是高的。有时需要具有更高灵敏度的拾波器以在低速下产生更高的输出。Intrinsically-safe magnetic pickups have a limited output current for use in hazardous locations where explosive gases may be present. These pickups will be approved by either CSA, UL or ATEX and it is important to read the applicable certificate that will have a description on where they are approved, which products they are approved with, as well as installation instructions. Similar to the standard pickups, these pickups have 2 pins that will accept a standard MS style connector and are available in short and long thread lengths. The sensitivity is available as either standard or high. A pickup with higher sensitivity is sometimes required to produce higher output at low speed.

 

Explosion-proof Magnetic Pickups
防爆磁性传感器

防爆磁性传感器采用带“NPT内螺纹”的盲端外壳建造,用于连接到NGID或柔性导管,包括电缆导管内的所有电线和连接,这种结构允许在可能存在爆炸性气体的危险位置使用。这些皮卡将由CSA、UL或ATEX批准,阅读适用证书非常重要,证书中应说明批准地点、批准的产品以及安装说明。这些皮卡有2-AWG 18导线,可以定制长度订购。螺纹体有短螺纹和长螺纹两种。Explosion-proof magnetic pickups are constructed using a blind-end housing with a "NPT female thread for connection to either ngid or flexible conduit By containing all wires and connections within the cable conduit,this construction allows for use in hazardous locations where explosive gases may be present. These pickups will be approved by either CSA, UL or ATEX and it is important to read the applicable certificate that will have a description on where they are approved, which products they are approved with, as well as installation instructions. These pickups have 2-AWG 18 leads that can be ordered in custom lengths. The bodies are available in short and long thread lengths.

 

- Magnetic Pickups and Speed Sensors

Lifetime Guarantee

All of Dynalco speed sensors are backed by a lifetime guarantee. Customers have piece of mind knowng their cost effective and reliable offering will operate in dirty, harsh and hazardous environments.

Hall Effect, TTL output sensors 霍尔效应、TTL 输出传感器、IECEx 认证

M101 Magnetic Pickup/Speed SensorM101 Magnetic Pickup / Speed Sensor

This standard variable reluctance magnetic pickup has standard sensitivity which makes it best suited for high speed (>500 rpm), large gear (>12 inch diam.) applications. It has a standard reach (1.125inches) and a 5/8-18 thread.
Dynalco

 

M101 Magnetic Pickup / Speed Sensor

This standard variable reluctance magnetic pickup has standard sensitivity which makes it best suited for high speed (>500 rpm), large gear (>12 inch diam.) applications. It has an extra long reach (6 inches) and a 5/8-18 thread.
Dynalco

M101 Magnetic Pickup/Speed SensorM102 Magnetic Pickup / Speed Sensor

This standard magnetic pickup has standard sensitivity which makes it best suited for high speed (>500 rpm), large gear (>12 inch diam.) applications. It has a standard reach (1.125inches) and a 5/8-18 thread.
Dynalco

 

M104 Magnetic Pickup/Speed SensorM104 Magnetic Pickup / Speed Sensor

This magnetic pickup has an explosion proof housing which makes it ideal for hazardous environments. It has a medium reach (1.875 inches) and 3/4-20 thread.
Dynalco

 

M107 Magnetic Pickup/Speed SensorM107 Magnetic Pickup / Speed Sensor

This standard magnetic pickup can power other instruments. It has standard sensitivity, standard reach (1.125 inches), and a 5/8-18 inch thread.
Dynalco

 

 

M107 Magnetic Pickup/Speed SensorM107 Magnetic Pickup / Speed Sensor

This standard magnetic pickup can power other instruments. It has standard sensitivity, standard reach (1.125 inches), and a 5/8-18 inch thread.
Dynalco

 

M131 Magnetic Pickup/Speed SensorM131 Magnetic Pickup / Speed Sensor

This standard magnetic pickup has standard sensitivity long reach (4.000inches) and a 5/8-18 thread.
Dynalco

 

M133 Magnetic Pickup/Speed SensorM133 Magnetic Pickup / Speed Sensor

This highly sensitivity magnetic pickup is well suited for lower speed (300 to 500 rpm) applications. It has long reach(4.000inches) and
5/8-18 thread.
Dynalco

M134 Magnetic Pickup/Speed SensorM134 Magnetic Pickup / Speed Sensor

This intrinsically-safe, low-output magnetic pickup has a standard reach (1.125 inches) & 5/8-18 thread
Dynalco

 

M135 Magnetic Pickup/Speed SensorM135 Magnetic Pickup / Speed Sensor

Intrinsically safe magnetic pickup with standard sensitivity, long reach (4.000inches) and a 5/8-18 thread.
Dynalco

 

M137 Magnetic Pickup/Speed SensorM137 Magnetic Pickup / Speed Sensor

This miniature magnetic pickup has standard sensitivity which is appropriate for higher speed (>500 rpm), small gear(less than 2 inch diameter) applications. It has a housing length of 1.250 inches and a 3/8-24 inch thread.
Dynalco

 

M138 Magnetic Pickup/Speed SensorM138 Magnetic Pickup / Speed Sensor

This miniature magnetic pickup is highly sensitive which makes it appropriate for lower speed (300 to 500 rpm), small gear (less than 2 inch diam.) applications. Its housing is 1.25 inches long with a 3/8-24 thread.
Dynalco

 

M142 Magnetic Pickup/Speed SensorM142 Magnetic Pickup / Speed Sensor

This standard magnetic pickup is ultra-sensitive making it appropriate for low speed (less than 300 rpm), larger gear(greater than 2 inch diam.)applications. It has a standard reach (1.125inches) and 5/8-18 thread.
Dynalco

 

M143 Magnetic Pickup/Speed SensorM143 Miniture Magnetic Pickup / Speed Sensor

This magnetic pickup has a micro-miniature housing and 14 inch leads. Its housing length is a short 0.875 inches and has a 10-32 thread. It is appropriate for small gear (less than 2 inch diam.) applications.
Dynalco

M151 Magnetic Pickup / Speed Sensor

This standard magnetic pickup has standard sensitivity which makes it appropriate for higher speed (>500 rpm), larger gear(greater than 2 inch diam.)applications. This pickup has a medium reach (2.500 inches)and a 5/8-18 thread.
Dynalco

 

M155 Magnetic Pickup / Speed Sensor

This special magnetic pickup is a low drag, flow meter sensor with thread x thread length x housing length = 5/8-18x1.125T x 2.250L.

Dynalco

M168 Magnetic Pickup / Speed SensorM168 Magnetic Pickup / Speed Sensor

This highly sensitive magnetic pickup is perfect for lower speed (300 to 500 rpm), larger gear (>2 inch diam.) applications. It has a 1.75" housing length, 5/8-18 thread and includes 12 inch leads.
Dynalco

M180 Explosionproof Magnetic Pickup / Speed Sensor

This magnetic pickup has an explosion proof housing which makes it ideal for hazardous environments. It is suited for use in standard temperature, mid speed (300 to 500 rpm), larger gear (>2 inch diam) applications. It has a standard reach (1.500 inches) and a 5/8-18 thread
Dynalco

M183 Magnetic Pick up / Speed Sensor

This highly sensitive magnetic pickup makes it good for mid-speed (300 to 500 rpm), larger gear (>2 inch diam.) applications. It has a medium reach (2.500 inches) and a 5/8-18 thread
Dynalco

M184 Magnetic Pick up / Speed Sensor

This ultra-sensitive magnetic pickup is perfect for low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a medium reach (2.500 inches) and a 5/8-18 thread.
Dynalco

 


M133 Magnetic Pickup/Speed Sensor

M185 Magnetic Pick up / Speed Sensor

This ultra-sensitive magnetic pickup is perfect for low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

M189 Magnetic Pick up / Speed Sensor

This standard magnetic pickup has standard sensitivity which makes it appropriate for high speed (>500 rpm), larger gear (>2 inch diam.) applications. It has a medium reach (2.500 inches) and a 5/8-18 thread.
Dynalco

M142 Magnetic Pickup/Speed SensorM201 Magnetic Pick up / Speed Sensor

The low output of this standard magnetic pickup makes it intrinsically safe and CSA approved for use in hazardous areas. It has a standard reach (1.125 inches) and 5/8-18 thread.
Dynalco

 

M142 Magnetic Pickup/Speed SensorM202 Magnetic Pick up / Speed Sensor

The low output of this standard magnetic pickup makes it intrinsically safe and CSA approved for use in hazardous areas. It has a standard reach (1.125 inches) and 5/8-18 thread.
Dynalco


M133 Magnetic Pickup/Speed SensorM203 Magnetic Pick up / Speed Sensor

This ultra-sensitive magnetic pickup is perfect for low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

 

M204 Magnetic Pick up / Speed Sensor

The zener-limited output of this magnetic pickup makes it intrinsically safe and CSA approved. It produces output even at low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a medium reach (2.5 inches) and a 5/8-18 thread.
Dynalco

 

M133 Magnetic Pickup/Speed SensorM205 Magnetic Pick up / Speed Sensor

This ultra-sensitive magnetic pickup is perfect for low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

 

M133 Magnetic Pickup/Speed SensorM207 Magnetic Pick up / Speed Sensor

This magnetic pickup can power other instruments. It produces output even at low speed (300 to 500 rpm) applications. It also has a long reach (4.000 inches), a 3/4-16 thread and is CSA approved.
Dynalco

 

M133 Magnetic Pickup/Speed SensorM208 Magnetic Pick up / Speed Sensor

This magnetic pickup can power other instruments. It has high sensitivity which produces output even at low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a long reach (4.000 inches), a 3/4-16 thread and is CSA approved.
Dynalco

 

M133 Magnetic Pickup/Speed SensorM231 Intrinsically Safe Magnetic Pick up / Speed Sensor

The low output of this magnetic pickup makes it intrinsically safe and CSA approved. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

M133 Magnetic Pickup/Speed SensorM233 Intrinsically Safe Magnetic Pick up / Speed Sensor

The low output of this magnetic pickup makes it intrinsically safe and CSA approved. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

 

M304 Magnetic Pick up / Speed Sensor

This magnetic pickup can power other instruments. It produces output even at low speed (300 to 500 rpm) applications. It also has a long reach (4.000 inches), a 3/4-16 thread and is CSA approved.
Dynalco

M319 Explosionproof Magnetic Pickup / Speed Sensor

This magnetic pickup has an explosion proof housing which makes it ideal for hazardous environments. It is a sensitive pickup suitable for mid-speed applications (300 to 500 rpm). It has a long reach (3.500 inches) and 3/4-20 UNEF thread.
Dynalco

M319 Magnetic Pickup/Speed SensorM319 Explosionproof Magnetic Pickup / Speed Sensor

This magnetic pickup has an explosion proof housing which makes it ideal for hazardous environments. It is a sensitive pickup suitable for mid-speed applications (300 to 500 rpm). It has a long reach (3.500 inches) and 5/8-18 thread.
Dynalco

M334 Minature Magnetic Pickup / Speed Sensor

This miniature magnetic pickup is highly sensitive which makes it appropriate for lower speed (300 to 500 rpm), small gear (less than 2 inch diam.) applications. Its housing is 1.25 inches long with a 3/8-24 thread. The pickup comes with 12 feet length of shielded cable.
Dynalco

M343 Bi-Directional Magnetic Pickup / Speed sensor

This special magnetic pickup is for exclusive use with DST-2000C, a direction-sensing tachometer. The M343 is a bi-directional, dual- output sensor with a 2.000 inch reach and 3/4-20 thread.
Dynalco

M343 Bi-Directional Magnetic Pickup / Speed sensor

This special magnetic pickup is for exclusive use with DST-2000C, a direction-sensing tachometer. The M343 is a bi-directional, dual- output sensor with a 2.000 inch reach and 3/4-20 thread.
Dynalco

 


Active, TTL and Hall Effect Sensors

M806 Magnetic Pick up / Speed Sensor, Hall Effect

This active magnetic pickup has digital TTL output suitable for zero velocity applications. It has a medium reach (2.500 inches) and a 5/8-18 thread.
Dynalco


M928 Magnetic Pick up / Speed Sensor with TTL output

This active magnetic pickup has digital TTL output suitable for zero velocity applications. It has a medium reach (2.500 inches) and a 5/8-18 thread.
Dynalco

M133 Magnetic Pickup/Speed SensorM928 Magnetic Pick up / Speed Sensor with TTL output

This active magnetic pickup has digital TTL output suitable for zero velocity applications. It has a medium reach (2.500 inches) and a 5/8-18 thread.
Dynalco

M133 Magnetic Pickup/Speed SensorM951 Magnetic Pick up / Speed Sensor, Hall Effect

This active magnetic pickup is a 24 VDC version of the standard model M928, with a digital TTL output suitable for zero velocity applications. It has a medium reach (2.500 inches) and a 5/8-18 thread.
Dynalco

 


Magnetic Pickups and Speed Sensors磁性速度传感器

Dynalco 成立于 1968 年,拥有三种产品,目标是为石油和天然气行业提供工程解决方案。47 年来,Dynalco以其在化学、海洋、采矿、石油和天然气以及电力行业中使用的高质量仪器和控制而闻名。

终身保修

所有 Dynalco 速度传感器均享有终身保修。客户知道他们经济高效且可靠的产品将在肮脏、恶劣和危险的环境中运行。

有用链接:霍尔效应、TTL 输出传感器、IECEx 认证

M101 磁性拾音器/速度传感器M101 磁性拾音器/速度传感器

这种标准可变磁阻磁性拾音器具有标准灵敏度,使其最适合高速 (>500 rpm)、大齿轮 (>12 英寸直径) 应用。它具有标准范围(1.125 英寸)和 5/8-18 螺纹。

 

M101 磁性拾音器/速度传感器

这种标准可变磁阻磁性拾音器具有标准灵敏度,使其最适合高速 (>500 rpm)、大齿轮 (>12 英寸直径) 应用。它具有超长触角(6 英寸)和 5/8-18 螺纹。

 

M101 磁性拾音器/速度传感器M102 磁性拾音器/速度传感器

这种标准磁性拾音器具有标准灵敏度,使其最适合高速 (>500 rpm)、大齿轮 (>12 英寸直径) 应用。它具有标准范围(1.125 英寸)和 5/8-18 螺纹。

 

M104 磁性拾音器/速度传感器M104 磁性拾音器/速度传感器

这款磁性拾音器具有防爆外壳,非常适合危险环境。它具有中等长度(1.875 英寸)和 3/4-20 螺纹。

 

M107 磁性拾音器/速度传感器M107 磁性拾音器/速度传感器

此标准磁性拾音器可为其他乐器供电。它具有标准灵敏度、标准范围(1.125 英寸)和 5/8-18 英寸螺纹。

 

M107 磁性拾音器/速度传感器M107 磁性拾音器/速度传感器

此标准磁性拾音器可为其他乐器供电。它具有标准灵敏度、标准范围(1.125 英寸)和 5/8-18 英寸螺纹。

 

M131 磁性拾音器/速度传感器M131 磁性拾音器/速度传感器

该标准磁性拾音器具有标准灵敏度长距离(4.000 英寸)和 5/8-18 螺纹。

 

M133 磁性拾音器/速度传感器M133 磁性拾音器/速度传感器

这种高灵敏度磁性拾音器非常适合低速(300 至 500 rpm)应用。它有长距离(4.000 英寸)和
5/8-18 螺纹。

 

M134 磁性拾音器/速度传感器M134 磁性拾音器/速度传感器

这款本质安全的低输出磁性拾音器具有标准范围(1.125 英寸)和 5/8-18 螺纹
Dynalco

 

M135 磁性拾音器/速度传感器M135 磁性拾音器/速度传感器

具有标准灵敏度、长距离(4.000 英寸)和 5/8-18 螺纹的本质安全磁性拾音器。

 

M137 磁性拾音器/速度传感器M137 磁性拾音器/速度传感器

这款微型磁性拾音器具有标准灵敏度,适用于更高速度(>500 rpm)、小齿轮(直径小于 2 英寸)的应用。它的外壳长度为 1.250 英寸,螺纹为 3/8-24 英寸。

 

M138 磁性拾音器/速度传感器M138 磁性拾音器/速度传感器

这种微型磁性拾音器非常灵敏,适用于低速(300 至 500 rpm)、小齿轮(直径小于 2 英寸)的应用。它的外壳长 1.25 英寸,螺纹为 3/8-24。

 

M142 磁性拾音器/速度传感器M142 磁性拾音器/速度传感器

该标准磁性拾音器具有超灵敏性,适用于低速(小于 300 rpm)、较大齿轮(大于 2 英寸直径)的应用。它具有标准范围(1.125 英寸)和 5/8-18 螺纹。

 

M143 磁性拾音器/速度传感器M143 微型磁性拾音器/速度传感器

这款磁性拾音器具有微型外壳和 14 英寸引线。它的外壳长度短 0.875 英寸,螺纹为 10-32。它适用于小齿轮(小于 2 英寸直径)应用。

 

M151 磁性拾音器/速度传感器

该标准磁性拾音器具有标准灵敏度,适用于更高速度(>500 rpm)、更大齿轮(大于 2 英寸直径)的应用。这款拾音器具有中等长度(2.500 英寸)和 5/8-18 螺纹。

 

M155 磁性拾音器/速度传感器
这种特殊的磁性拾音器是一种低阻力流量计传感器,螺纹 x 螺纹长度 x 外壳长度 = 5/8-18x1.125T x 2.250L。

 

 

M168 磁性拾音器/速度传感器M168 磁性拾音器/速度传感器

这种高度灵敏的磁性拾音器非常适合低速(300 至 500 rpm)、较大齿轮(> 2 英寸直径)的应用。它的外壳长度为 1.75",螺纹为 5/8-18,包括 12 英寸引线
。Dynalco

 

M180防爆磁性拾音器/速度传感器

这款磁性拾音器具有防爆外壳,非常适合危险环境。它适用于标准温度、中速(300 至 500 rpm)、较大齿轮(> 2 英寸直径)的应用。它具有标准范围(1.500 英寸)和 5/8-18 螺纹
Dynalco

 

M183 磁性拾音器/速度传感器

这种高度灵敏的磁性拾音器非常适合中速(300 至 500 rpm)、较大的齿轮(> 2 英寸直径)应用。它具有中等长度(2.500 英寸)和 5/8-18 螺纹
Dynalco

 

M184 磁性拾音器/速度传感器

这款超灵敏磁性拾音器非常适合低速 (<300 rpm)、较大齿轮 (>2 英寸直径) 的应用。它具有中等长度(2.500 英寸)和 5/8-18 螺纹。


M133 磁性拾音器/速度传感器

M185 磁性拾音器/速度传感器

这款超灵敏磁性拾音器非常适合低速 (<300 rpm)、较大齿轮 (>2 英寸直径) 的应用。它有很长的触角(4.000 英寸)和 5/8-18 螺纹。

 

M189 磁性拾音器/速度传感器

该标准磁性拾音器具有标准灵敏度,适用于高速 (>500 rpm)、较大齿轮 (>2 英寸直径) 的应用。它具有中等长度(2.500 英寸)和 5/8-18 螺纹。

 

M142 磁性拾音器/速度传感器M201 磁性拾音器/速度传感器

这种标准磁性拾音器的低输出使其本质安全,并获得 CSA 批准可用于危险区域。它具有标准范围(1.125 英寸)和 5/8-18 螺纹。

 

M142 磁性拾音器/速度传感器M202 磁性拾音器/速度传感器

这种标准磁性拾音器的低输出使其本质安全,并获得 CSA 批准可用于危险区域。它具有标准范围(1.125 英寸)和 5/8-18 螺纹。

 

M133 磁性拾音器/速度传感器M203 磁性拾音器/速度传感器

这款超灵敏磁性拾音器非常适合低速 (<300 rpm)、较大齿轮 (>2 英寸直径) 的应用。它有很长的触角(4.000 英寸)和 5/8-18 螺纹。

 

M204 磁性拾音器/速度传感器

The zener-limited output of this magnetic pickup makes it intrinsically safe and CSA approved. It produces output even at low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a medium reach (2.5 inches) and a 5/8-18 thread.
Dynalco

 

M133 磁性拾音器/速度传感器M205 Magnetic Pick up / Speed Sensor

This ultra-sensitive magnetic pickup is perfect for low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

 

M133 磁性拾音器/速度传感器M207 Magnetic Pick up / Speed Sensor

This magnetic pickup can power other instruments. It produces output even at low speed (300 to 500 rpm) applications. It also has a long reach (4.000 inches), a 3/4-16 thread and is CSA approved.
Dynalco

 

M133 磁性拾音器/速度传感器M208 Magnetic Pick up / Speed Sensor

This magnetic pickup can power other instruments. It has high sensitivity which produces output even at low speed (<300 rpm), larger gear (>2 inch diam.) applications. It has a long reach (4.000 inches), a 3/4-16 thread and is CSA approved.
Dynalco

 

M133 磁性拾音器/速度传感器M231 Intrinsically Safe Magnetic Pick up / Speed Sensor

The low output of this magnetic pickup makes it intrinsically safe and CSA approved. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

 

M133 磁性拾音器/速度传感器M233 Intrinsically Safe Magnetic Pick up / Speed Sensor

The low output of this magnetic pickup makes it intrinsically safe and CSA approved. It has a long reach (4.000 inches) and a 5/8-18 thread.
Dynalco

 

M304 Magnetic Pick up / Speed Sensor

This magnetic pickup can power other instruments. It produces output even at low speed (300 to 500 rpm) applications. It also has a long reach (4.000 inches), a 3/4-16 thread and is CSA approved.
Dynalco

 

M319 Explosionproof Magnetic Pickup / Speed Sensor

This magnetic pickup has an explosion proof housing which makes it ideal for hazardous environments. It is a sensitive pickup suitable for mid-speed applications (300 to 500 rpm). It has a long reach (3.500 inches) and 3/4-20 UNEF thread.
Dynalco

 

M319 磁性拾音器/速度传感器M319 Explosionproof Magnetic Pickup / Speed Sensor

This magnetic pickup has an explosion proof housing which makes it ideal for hazardous environments. It is a sensitive pickup suitable for mid-speed applications (300 to 500 rpm). It has a long reach (3.500 inches) and 5/8-18 thread.
Dynalco

 

M319 磁性拾音器/速度传感器

M321 IECEx 批准的磁性拾音器/速度传感器

该标准可变磁阻 IECEx 批准的磁性拾音器具有标准灵敏度,使其最适合速度 > 300 rpm、大齿轮(> 12 英寸直径)。它可以选择螺纹长度、螺纹类型(公制和英制)和电气连接。

IECEx Ex mb IIC 和 Ex ia IIC 双重认证

M321 IECEx Approved Magnetic Pickup / Speed Sensor

This standard variable reluctance IECEx approved magnetic pickup has standard sensitivity which makes it best suited for speeds >300 rpm, large gear (>12 inch diam.). It has a choice of threaded lengths, thread type (Metrix and imperial) and electrical connections.

Dual approval for IECEx Ex mb IIC and Ex ia IIC

Data Sheet IECEx certificate

 

M334 Miniature Magnetic Pickup / Speed Sensor

This miniature magnetic pickup is highly sensitive which makes it appropriate for lower speed (300 to 500 rpm), small gear (less than 2 inch diam.) applications. Its housing is 1.25 inches long with a 3/8-24 thread. The pickup comes with 12 feet length of shielded cable.
Dynalco

 

 

M343 Bi-Directional Magnetic Pickup / Speed sensor

This special magnetic pickup is for exclusive use with DST-2000C, a direction-sensing tachometer. The M343 is a bi-directional, dual- output sensor with a 2.000 inch reach and 3/4-20 thread.
Dynalco

 

M343 Bi-Directional Magnetic Pickup / Speed sensor

This special magnetic pickup is for exclusive use with DST-2000C, a direction-sensing tachometer. The M343 is a bi-directional, dual- output sensor with a 2.000 inch reach and 3/4-20 thread.
Dynalco


M319 磁性拾音器/速度传感器

 

 

Active, TTL and Hall Effect Sensors
有源、TTL 和霍尔效应传感器

 

M920 IECEx 批准的磁性拾音器/速度传感器,霍尔效应传感器

这款经 IECEx 批准的磁性拾音器具有密封外壳,非常适合危险环境。这种有源磁性拾音器具有数字 TTL 输出,适用于高达 20,000 Hz 的零速度应用。它可以选择螺纹长度、螺纹类型(公制和英制)和电气连接。

IECEx Ex mb IIC 和 Ex ia IIC 双重认证

数据表IECEx 证书

M920 IECEx Approved Magnetic Pickup / Speed Sensor, Hall Effect

This IECEx approved magnetic pickup has an encapsulated housing which makes it ideal for hazardous environments. This active magnetic pickup has digital TTL output suitable for zero velocity applications up to 20,000 Hz.. It has a choice of threaded lengths, thread type (Metrix and imperial) and electrical connections.

Dual approval for IECEx Ex mb IIC and Ex ia IIC

Data Sheet IECEx certificate

 

M806 磁性拾音器/速度传感器,霍尔效应

这种有源磁性拾音器具有适用于零速度应用的数字 TTL 输出。它具有中等长度(2.500 英寸)和 5/8-18 螺纹。

 

 

M928 磁性拾音器/速度传感器,带 TTL 输出

这种有源磁性拾音器具有适用于零速度应用的数字 TTL 输出。它具有中等长度(2.500 英寸)和 5/8-18 螺纹。

 

M133 磁性拾音器/速度传感器M928 磁性拾音器/速度传感器,带 TTL 输出

这种有源磁性拾音器具有适用于零速度应用的数字 TTL 输出。它具有中等长度(2.500 英寸)和 5/8-18 螺纹。

 

M133 磁性拾音器/速度传感器M951 磁性拾音器/速度传感器,霍尔效应

这种有源磁性拾音器是标准型号 M928 的 24 VDC 版本,带有适用于零速度应用的数字 TTL 输出。它具有中等长度(2.500 英寸)和 5/8-18 螺纹。

 

 

   


美国DMK Engineering Solutions公司
信德迈科技(北京)有限公司 CNMEC Technology


地址:北京市朝阳区望京街10号望京SOHO塔1C座2115室
邮编:100102
电话:010-8428 2935, 8428 9077, 8428 3983
手机:139 101 22694
Http://www.cnmec.biz
E-mail:sales@cnmec.biz
传真:010-8428 8762

京ICP备08000876号-1
京公网安备 11010502019740
Since 2007 Strong Distribution & Powerful Partnerships